- |
SIMATIC DP, ET 200ECO PN, 4 AO U/I; 4 X M12, DEGREE OF PROTECTION IP67 |
|
| General information |
| Vendor identification (VendorID) |
002AH |
| Device identifier (DeviceID) |
0306H |
| Supply voltage |
| 24 V DC |
Yes |
| permissible range, lower limit (DC) |
20.4 V |
| permissible range, upper limit (DC) |
28.8 V |
| Reverse polarity protection |
Yes |
| Input current |
| Current consumption, typ. |
280 mA |
| Encoder supply |
| Number of outputs |
4 |
| 24 V encoder supply |
| short-circuit protection |
Yes; Electronic at 1.4 A |
| Output current, max. |
1 A |
| Power losses |
| Power loss, typ. |
5.5 W |
| Analog outputs |
| Number of analog outputs |
4 |
| Voltage output, short-circuit protection |
Yes |
| Voltage output, short-circuit current, max. |
30 mA |
| Current output, no-load voltage, max. |
20 V |
| Output ranges, voltage |
| 0 to 10 V |
Yes |
| 1 to 5 V |
Yes |
| -10 to +10 V |
Yes |
| Output ranges, current |
| 0 to 20 mA |
Yes |
| -20 to +20 mA |
Yes |
| 4 to 20 mA |
Yes |
| Connection of actuators |
| for voltage output two-wire connection |
Yes |
| for current output two-wire connection |
Yes |
| Load impedance (in rated range of output) |
| with voltage outputs, min. |
1 kΩ |
| with voltage outputs, capacitive load, max. |
1 µF |
| with current outputs, max. |
600 Ω |
| with current outputs, inductive load, max. |
1 mH |
| Destruction limits against externally applied voltages and currents |
| Voltages at the outputs towards MANA |
28.8 V permanent, 35 V for max. 500 ms |
| Cable length |
| Cable length, shielded, max. |
30 m |
| Analog value creation |
| Analog value display |
SIMATIC S7 format |
| Measurement principle |
Resistor network |
| Integrations and conversion time/resolution per channel |
| Resolution (incl. overrange) |
15 bits + sign |
| Conversion time (per channel) |
1 ms |
| Settling time |
| for resistive load |
2 ms |
| for capacitive load |
1.8 ms |
| for inductive load |
2 ms |
| Errors/accuracies |
| Output ripple (based on output area, bandwidth 0 to 50 kHz), (+/-) |
U: ±0.6 mVrms; I: ±0.4 nArms |
| Linearity error (relative to output range), (+/-) |
0.02 % |
| Crosstalk between the outputs, min. |
70 dB |
| Repeat accuracy in steady state at 25 °C (relative to output area), (+/-) |
0.0080 % |
| Interfaces |
| Transmission procedure |
100BASE-TX |
| Transmission rate, max. |
100 Mbit/s |
| Supports protocol for PROFINET IO |
| Number of PROFINET interfaces |
1 |
| Autocrossing |
Yes |
| Automatic detection of transmission speed |
Yes |
| Integrated switch |
Yes |
| PROFINET IO Device |
| IRT with the option "high flexibility" supported |
Yes |
| Prioritized startup |
Yes |
| Protocols |
| Supports protocol for PROFINET IO |
Yes |
| PROFINET CBA |
No |
| Supports protocol for PROFIsafe |
No |
| Protocols (Ethernet) |
| SNMP |
Yes |
| DCP |
Yes |
| LLDP |
Yes |
| ping |
Yes |
| ARP |
Yes |
| Interrupts/diagnostics/status information |
| Status indicator |
Yes |
| Substitute values connectable |
Yes |
| Alarms |
| Diagnostic alarm |
Yes |
| Diagnostic messages |
| Diagnostic functions |
Yes |
| Diagnostic information readable |
Yes |
| Monitoring the supply voltage |
Yes; Green "ON" LED |
| Wire break |
Yes; Channel-by-channel with current output |
| Short circuit |
Yes; Channel-by-channel with voltage output |
| Group error |
Yes; Red/yellow "SF/MT" LED |
| Galvanic isolation |
| between the load voltages |
Yes |
| between load voltage and all other switching components |
No |
| between Ethernet and electronics |
Yes |
| Galvanic isolation analog outputs |
| between the channels |
No |
| Permissible potential difference |
| between M internally and the outputs |
10 Vpp AC |
| Degree and class of protection |
| IP65 |
Yes |
| IP66 |
Yes |
| IP67 |
Yes |
| Connection method |
| M12 |
Yes |
| Dimensions |
| Width |
60 mm |
| Height |
175 mm |
| Depth |
49 mm |
| Weights |
| Weight (without packaging) |
930 g |
| Status |
May 26, 2014 |
